Here are typical installation guidelines for an ONAN 5500 Gas/Diesel/Propane having a 8-pin generator wiring harness.
Note: For action 7 you will have to buy 14-gauge electric cable for the run from our ShorePower track to your transfer switch.
STEP ONE:
Turn-off your generator AC circuit breakers in order to avoid disruption of coast energy solution during testing and installation of ShorePower track.
STEP TWO:
Determine the following 4 cables on your own generator wiring harness.
Work with a label or tape to mark each cable so that you won't forget which wire is which.
- A – Ground – Brown
- B – Stop – Green
- C – Begin – Red
- E – Run – Orange
The wires are labeled on the harness as follows on a typical ONAN 10-pin wiring harness
- A – Ground
- C – Begin
- E – Stop
- F – Run
NOTE: The pin connections above are typical ONAN connections. Only a few ONAN generators have actually the generator that is same harness connections as some might have been changed because of the dealer or RV maker. Make certain you have actually correctly identified the 4 wires properly before proceeding with step three.
STEP THREE:
Connect one Posi-Tap to each regarding the 4 cables identified in step two.
STEP FOUR:
Result in the connection from the ShorePower track into the Posi-Taps (wiring harness) according to the wiring diagram provided.
- Green wire to E AVOID
- Red cable to C BEGIN
- Brown cable to A GROUND
- Orange cable to FRUN
Remember to link the proper wires to the wiring harness once we utilize red-colored cables https://rose-brides.com/ over and over again.
On our installation photo we utilized white cables to expand to your harness as a result of location of y our device. The closer the installation of our product into the wiring harness will assist you to make use of the supplied 4-foot wire size we offer.
ACTION 5:
- Connect the wire that is red the ShorePower Monitor (I3) to 1 part of this enable switch utilising the provided Posi-Lock or a crimp connector.
- Link the 2nd red cable (supplied in the zip-lock case) to another region of the switch that is enable. One other end of the red cable will ultimately link to your good battery pack terminal.
ACTION 6:
- Link the red cable through the enable switch as well as the red cable from (L+) in the ShorePower track to your +12 VDC (good battery terminal).
- Link the wire that is blackM) in the ShorePower track to ground (any steel in your RV).
STEP 7:
Through the ShorePower Monitor Power Converter ( See diagram that is wiring – Transfer Switch Connection):
You'll need 14-gauge stranded electrical cable for the run from our product to your transfer switch.
- Connect (L) on our MeanWell Power Converter to 1 region of the 110 Volts regarding the transfer switch.
- Link the (N) on our MeanWell Power Converter towards the center connection (common) regarding the transfer switch
ACTION 8:
The ShorePower track & the MeanWell Power Converter should both have their light that is green ON if all of the cables, like the cables into the transfer switch, are properly linked. .
- To try the machine switch on the ALLOW Switch and disconnect from coast power. The light that is green the MeanWell goes off and in more or less 20 moments our unit will auto-start your generator.
- Let generator run for approximately one minute then re-connect to shore energy and our product will immediately shut-off your generator in more or less seconds that are 10-12. The green light on the MeanWell should come straight straight back on.
SIGNIFICANT NOTE: switching the ALLOW CHANGE On or OFF will not impact the light that is green the ShorePower Monitor or MeanWell. IF the ShorePower track is correctly link along with shore energy those two light can be on. The ENABLE CHANGE merely allows or disables monitoring.
This is just what a set-up that is typical appear to be when it is completed. You will see other consumer installation photos by clicking right right right here.